1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

解决方案搜索 - 热插拔控制器

DC2578A - Total Power Management: Hot Swap, Intermediate Bus Voltage, Point-of-Load (featuring LTC4281, LTC3886, LTC3887, LTC2975) [requires DC1613]

Jan 18th 2018
The DC2578A is a complete power chain, including a hot swap controller, an intermediate bus controller, and six point-of-load channels with power system management. The board demonstrates how to safely transfer power from a backplane, through an LTC4281 hot swap controller, through an LTC3886 step-down intermediate bus controller ...

Demo Board LTpowerPlay 

 

DC2442A - LTC4282 Demo Board | 200A Hot Swap Controller with Telemetry [requires DC1613]

Jul 18th 2017
Demonstration circuit 2442A features the LTC®4282 high current Hot Swap controller. The LTC4282 is well suited to high power applications because the precise monitoring capability and accurate current limiting reduces the extremes in which both loads and power supplies must safely operate. Nonvolatile configuration allows ...

Demo Board LTpowerPlay 

 

LTspice Models of ISO 7637-2 & ISO 16750-2 Transients

Dan Eddleman - 高级应用工程师 Apr 5th 2017
Introduction Simulating the ISO 7637-2 and ISO 16750-2 transients early in the design phase of an automotive product can pinpoint issues that would otherwise come to light during electromagnetic compatibility (EMC) testing. If a product fails EMC testing, hardware modifications are required, project schedules suffer, and extra ...

Blog Post LTspice 

 

DC2423A-B - LTM9100 Demo Board | Isolated 380V Switch Controller with Telemetry [requires DC590 or DC2026]

Mar 8th 2017
Demonstration circuit 2423A showcases the LTM®9100 Isolated Switch Controller in either a typical 48V application (–A) or in a high voltage 380V application (–B). The board may be configured for either high side or low side operation, dependent on the connection of external supply and load to the banana jacks. ...

Demo Board Linduino QuikEval System 

 

DC2423A-A - LTM9100 Demo Board | Isolated 48V Switch Controller with Telemetry [requires DC590 or DC2026]

Mar 8th 2017
Demonstration circuit 2423A showcases the LTM®9100 Isolated Switch Controller in either a typical 48V application (–A) or in a high voltage 380V application (–B). The board may be configured for either high side or low side operation, dependent on the connection of external supply and load to the banana jacks. ...

Demo Board Linduino QuikEval System 

 

隔离式 Anyside 开关控制器保护和监视高达 1000VDC 的电源

Feb 27th 2017
加利福尼亚州米尔皮塔斯 (MILPITAS, CA) – 2017 年 2 月 27 日 –  凌力尔特公司 (Linear Technology Corporation) 推出 µModule® (微型模块) 一体化隔离式 Anyside™ 开关控制器 LTM9100,该器件保护并监视高达 1000V 的高压 DC 电源。用于工业、数据通信、航空电子和医疗应用的高压电源需要受控接通,并需要隔离以控制电路保护、操作人员安全并断开接地通路 ...

Press Release 

 

DC536B-A - LTC4211CMS Demoboard | 7A Electronic Circuit Breaker and Hot Swap Controller

Jan 27th 2017
Demonstration circuit 536B is a hot swap controller with multifunction current control featuring the LTC®4211. The DC536B-A is configured to operate with up to 7A load and DC536B-B up to 20A load. ...

Demo Board 

 

DC1356A - LTC1645CS8 Demoboard | 2-Supply Hot Swap Controller and Sequencer [5V/5A, 3.3V/7A]

Nov 23rd 2016
Demonstration circuit 1356A is a dual hot swap circuit featuring the LTC®1645 dual-channel hot swap controller/ power sequencer. ...

Demo Board 

 

DC2278A-B - LTC4281 Demo Board with Programming Socket | 12V, 50A Hot Swap Controller with Telemetry [requires DC1613]

Sep 23rd 2016
Demonstration circuit 2278A features the LTC®4281 hot swap controller. The LTC4281 is well suited to high power applications because the precise monitoring capability and accurate current limiting reduces the extremes in which both loads and power supplies must safely operate. Non-volatile configuration allows for flexibility ...

Demo Board LTpowerPlay 

 

DC2278A-A - LTC4281 Demo Board | 12V, 50A Hot Swap Controller with Telemetry [requires DC1613]

Sep 23rd 2016
Demonstration circuit 2278A features the LTC®4281 hot swap controller. The LTC4281 is well suited to high power applications because the precise monitoring capability and accurate current limiting reduces the extremes in which both loads and power supplies must safely operate. Non-volatile configuration allows for flexibility ...

Demo Board LTpowerPlay 

 

LTspice SOAtherm Support for PCB and Heat Sink Thermal Models

Dan Eddleman - 高级应用工程师 Sep 1st 2016
The SOAtherm model distributed with LTspice software and simplifies Hot Swap and Surge Stopper designs by verifying directly within a circuit simulation that a particular MOSFET’s Safe Operating Area (SOA) is not exceeded. This article assumes a basic understanding of the SOAtherm model. If you are not familiar with SOAtherm, ...

Blog Post LTspice 

 

LTC4282 具 I2C 接口的双路、高电流 (100A) 热插拔控制器 – 视频产品概要

Pinkesh Sachdev - 产品市场工程师 - 混合信号 Aug 25th 2016
LTC4282 热插拔控制器允许在一块带电背板上安全地进行电路板的插拔操作。通过采用一个或多个外部 N 沟道传输晶体管,可使电路板电源电压和浪涌电流以一种可调速率斜坡上升。一个 I2C 接口和内置 ADC 实现了电路板电流、电压、功率、能量和故障状态的监视功能 ...

Video 

 

浪涌抑制器:过压和过流保护 IC – 视频产品概要

Pinkesh Sachdev - 产品市场工程师 - 混合信号 Aug 25th 2016
传统上,过压和过流保护 (例如:抛负载保护) 是采用庞大的电容器、TVS 二极管和熔丝实现的,但是此类分立式解决方案会占用大量的电路板空间,而且在瞬变过程中并不提供持续运作。凌力尔特的高电压浪涌抑制器、过压保护、过流保护和电路断路器 ...

Video 

 

LTC4233 / LTC4234 具保证安全工作区 (SOA) 的 10A / 20A 热插拔控制器 – 视频产品概要

Pinkesh Sachdev - 产品市场工程师 - 混合信号 Aug 25th 2016
LTC4233 和 LTC4234 是针对热插拔应用的集成型解决方案,允许电路板在带电背板上安全地插入和拔出。这些器件把一个热插拔控制器、功率 MOSFET 和电流检测电阻器集成在单个封装中,以满足小型化应用的要求。对 MOSFET 的安全工作区进行了生产测试,并保证其能承受热插拔应用中的应力 ...

Video 

 

DC2024A-B - LTC4282 Demo Board with Programming Socket | 100A Hot Swap Controller with Telemetry [requires DC1613]

Jun 7th 2016
Demonstration circuit 2024A features the LTC®4282 high current Hot Swap™ controller. The LTC4282 is well suited to high power applications because the precise monitoring capability and accurate current limiting reduces the extremes in which both loads and power supplies must safely operate. Non-volatile configuration ...

Demo Board Linduino LTpowerPlay 

 

LTspice: Using Time-Dependent Exponential Sources to Model Transients

Mitchell Lee - 应用工程师
Gabino Alonso - 市场策略工程师
May 15th 2016
When working with Surge Stoppers or Hot Swap Controllers, occasionally there is a need to simulate a circuit's behavior with a specified voltage or current transient. These transients are usually modeled using a double exponential waveform characterized by a peak voltage, a rise time (usually 10%–90%), a fall time to 50% ...

Blog Post LTspice 

 

DC2178A-B - LTC4380IDD-2 Demo Board | Low Quiescent Current Surge Stopper, Auto-Retry Version

May 5th 2016
Demonstration circuit 2178A showcases the LTC®4380 low quiescent current surge stopper in an application which can be configured for 12V, 1A or 24V/28V, 0.5A operation. The output voltage is clamped by the LTC4380, permitting the load to operate uninterrupted during transients of up to 250V and load dump surges such as ISO-16750-2 ...

Demo Board 

 

DC2178A-A - LTC4380IDD-1 Demo Board | Low Quiescent Current Surge Stopper, Latchoff Version

May 5th 2016
Demonstration circuit 2178A showcases the LTC®4380 low quiescent current surge stopper in an application which can be configured for 12V, 1A or 24V/28V, 0.5A operation. The output voltage is clamped by the LTC4380, permitting the load to operate uninterrupted during transients of up to 250V and load dump surges such as ISO-16750-2 ...

Demo Board 

 

DC2314A-B - LTC4236-2 Demo Board | Dual Ideal Diode-OR & Single Hot Swap Controller with Current Monitor, Auto-Retry Version

Mar 22nd 2016
Demonstration circuit 2314A is intended to demonstrate the performance of the LTC4236-1/LTC4236-2 Dual Ideal Diode-OR and Single Hot Swap Controller with Current Monitor. The controller operates in redundant supply circuits, where each rail has an individual ideal diode, and the outputs are connected to the load through a single ...

Demo Board 

 

DC2314A-A - LTC4236-1 Demo Board | Dual Ideal Diode-OR & Single Hot Swap Controller with Current Monitor, Latch-Off Version

Mar 22nd 2016
Demonstration circuit 2314A is intended to demonstrate the performance of the LTC4236-1/LTC4236-2 Dual Ideal Diode-OR and Single Hot Swap Controller with Current Monitor. The controller operates in redundant supply circuits, where each rail has an individual ideal diode, and the outputs are connected to the load through a single ...

Demo Board 

 

DC2315A-B - LTC4235-2 Demo Board | Dual 12V Ideal Diode-OR & Single Hot Swap Controller with Current Monitor, Auto-Retry

Jan 12th 2016
Demonstration circuit 2315A is intended to demonstrate the performance of the LTC®4235-1/LTC4235-2 Dual 12V Ideal Diode-OR and Single Hot Swap™ Controller with Current Monitor. The controller operates in redundant 12V supply circuits, where each rail has an individual ideal diode, and the outputs are connected to the ...

Demo Board 

 

DC2315A-A - LTC4235-1 Demo Board | Dual 12V Ideal Diode-OR & Single Hot Swap Controller with Current Monitor, Latch-Off

Jan 12th 2016
Demonstration circuit 2315A is intended to demonstrate the performance of the LTC®4235-1/LTC4235-2 Dual 12V Ideal Diode-OR and Single Hot Swap™ Controller with Current Monitor. The controller operates in redundant 12V supply circuits, where each rail has an individual ideal diode, and the outputs are connected to the ...

Demo Board 

 

Ideal Diode-OR & Hot Swap Controller Provides Current Monitoring Output

Jan 6th 2016
MILPITAS, CA - January 6, 2016 - Linear Technology Corporation introduces the LTC4236, a dual ideal diode-OR and single Hot Swap controller with a load current monitoring output. High availability systems-servers, network routers, and solid-state drives-power circuit boards with multiple power supply feeds. The LTC4236 combines ...

Press Release 

 

具功率均分和遥测功能的高功率热插拔

Josh Simonson - 设计工程师 Dec 4th 2015
热插拔电路越来越多地在高于 1000W 的功率级别上使用。在这些功率级别上需要多个开关 MOSFET,但是在调节电流时增设 MOSFET 并不会改善电路的功率耗散能力,因为 MOSFET 不具备均分电流的固有特性。LTC4282 通过把 MOSFET 分为两个具有独立电流限值 (其可强化两组之间的功率均分) ...

Video 

 

DC2024A-A - LTC4282 Demo Board | 100A Hot Swap Controller with Telemetry [requires DC1613]

Nov 25th 2015
Demonstration circuit 2024A features the LTC®4282 high current Hot Swap™ controller. The LTC4282 is well suited to high power applications because the precise monitoring capability and accurate current limiting reduces the extremes in which both loads and power supplies must safely operate. Non-volatile configuration ...

Demo Board Linduino LTpowerPlay 

 

Energy Monitoring Hot Swap Controller Enables 100A Board Designs

Oct 1st 2015
MILPITAS, CA - October 1, 2015 - Linear Technology Corporation introduces the LTC4282, an energy monitoring Hot Swap controller with dual MOSFET drive to enable 100A and higher current board designs. The LTC4282 ensures safe board insertion and removal from live 2.9V to 33V backplanes by controlling external N-channel MOSFETs ...

Press Release 

 

DC2116A-B - LTC4233 Demo Board | 10A Guaranteed SOA Hot Swap Controller

Aug 7th 2015
Demonstration circuit 2116A features the LTC4233/ LTC®4234 10A/20A Guaranteed SOA Hot Swap™ Controllers. The LTC4233 and LTC4234 are ideally suited for compact power distribution control in 2.9V to 15V applications for hot board insertion protection, high side power switching, and electronic circuit breaker functions. ...

Demo Board 

 

利用保证的 SOA 在高电流热插拔应用中实现低导通电阻

Dan Eddleman - 高级应用工程师
Gabino Alonso - 市场策略工程师
Jul 29th 2015
引言 ~~ 在高电流背板应用中要求实现电路板的带电插拔,这就需要兼具低导通电阻 (在稳态操作期间) 和针对瞬态情况之高安全工作区 (SOA) 的 MOSFET。通常,专为拥有低导通电阻而优化的新式 MOSFET 并不适合高 SOA 热插拔应用。 LTC®4234 是一款针对热插拔 ...

Blog Post Circuit LTspice 

 

DC2116A-A - LTC4234 Demo Board: 20A Guaranteed SOA Hot Swap Controller

May 27th 2015
Demonstration circuit 2116A features the LTC4233/ LTC®4234 10A/20A Guaranteed SOA Hot Swap™ Controllers. The LTC4233 and LTC4234 are ideally suited for compact power distribution control in 2.9V to 15V applications for hot board insertion protection, high side power switching, and electronic circuit breaker functions. ...

Demo Board 

 

Compact 20A Hot Swap Controller Integrates MOSFET & Current Sensing

Apr 27th 2015
MILPITAS, CA - April 27, 2015 - Linear Technology Corporation introduces the LTC4234, a 20A Hot Swap™ controller with integrated MOSFET and current sensing, providing a small footprint hot-plug solution for high density circuit boards. The LTC4234 ensures safe board insertion and removal from live 2.9V to 15V backplanes by controlling ...

Press Release 

 

LTC7860 高效率开关浪涌抑制器 - 视频产品概要

Bruce Haug - 产品市场工程师 Mar 24th 2015
LTC7860 高效率浪涌抑制器可保护负载免遭高压瞬变的损坏。高效率可提供较高的电流和较小的解决方案尺寸。在输入过压过程中 (例如:车辆中的负载突降),LTC7860 通过控制一个外部 MOSFET 的栅极以充当一个开关 DC/DC 稳压器 (保护性 PWM 模式)。该操作把输出电压调节至一个安全的电平,从而允许负载在输入过压过程中运作 ...

Video 

 

LTC2956 微功率、电池反向保护按钮控制器和睡眠定时器具热插拔控制器

Mar 19th 2015
LTC2956 是一款具按钮控制功能的微功率、宽输入电压范围、可配置唤醒定时器。其周期地唤醒和接通一个连接系统以执行诸如监视温度或捕获图像等任务。在完成任务之后,LTC2956 关闭系统以节省电能。  ...

Circuit 

 

LTC4218 12V / 100A Hot Swap Design for Server Farms

Dan Eddleman - 高级应用工程师 Mar 18th 2015
Cultivate reliability on the farm with a properly designed Hot Swap circuit. Introduction As data centers servicing the cloud grow in speed and capacity, backplane supplies are called on to deliver currents that push the performance boundaries of Hot Swap™ components. Hot Swap solutions allow boards to be inserted and ...

Blog Post Circuit LTspice 

 

LTC4226 Parallel MOSFETs in Hot Swap Circuits

Dan Eddleman - 高级应用工程师
Gabino Alonso - 市场策略工程师
Mar 13th 2015
The Good, the Bad, and the Ugly Introduction While it is often desirable, and sometimes absolutely critical, to use multiple parallel MOSFETs in Hot Swap™ circuits, careful analysis of Safe Operating Area (SOA) is essential. Each additional parallel MOSFET added to a circuit improves the voltage drop, power loss, and ...

Blog Post Circuit LTspice 

 

Understanding Power Monitor Accuracy

Mark Thoren - 科学专家 - 混合信号
Hamza Salman Afzal - 应用工程师
Feb 20th 2015
Measurement of a system’s power consumption during a final factory test (before deployment into the field) is a prudent part of a test program for any product. But there is an increasing emphasis to bring this functionality into the product itself for “run-time” monitoring of power, current, supply voltage, ...

Blog Post 

 

Surge Stoppers Ease MIL-STD-1275D Compliance

Dan Eddleman - 高级应用工程师 Nov 25th 2014
Introduction A military vehicle is a tough environment for electronics, where the potential for damaging power supply fluctuations is high. U.S. Department of Defense MILSTD- 1275D sets down the requirements for electronics when powered from a 28V supply, ensuring that electronics survive in the field. MIL-STD-1275D compliance ...

Blog Post 

 

DC2161A-B - LTC4231IMS-2 Demo Board | Micropower Hot Swap Controller with Auto-Retry

Nov 11th 2014
Demonstration circuit 2161A showcases the LTC®4231 Micropower Hot Swap™ Controller in a 12V, 3A application. Included on the board are input overvoltage and reverse voltage protection, input voltage dividers for UV and OV detection, an output voltage LED, jumpers to disable UV/OV, manual and remote enable control, ...

Demo Board 

 

DC2161A-A - LTC4231IMS-1 Demo Board | Micropower Hot Swap Controller with Latch-Off

Nov 11th 2014
Demonstration circuit 2161A showcases the LTC®4231 Micropower Hot Swap™ Controller in a 12V, 3A application. Included on the board are input overvoltage and reverse voltage protection, input voltage dividers for UV and OV detection, an output voltage LED, jumpers to disable UV/OV, manual and remote enable control, ...

Demo Board 

 

DC1886B-B - LTC4232IDHC-1 Demo Board | 5A Integrated Hot Swap Controller with 16ms Turn-On Delay

Oct 13th 2014
Demonstration circuit 1886B features the LTC4232 and the LTC4232-1 5A integrated Hot Swap™ controllers. The LTC4232 is ideally suited for demanding power distribution control in 2.9V to 15V applications for hot board insertion protection, high side power switching, and electronic circuit breaker functions. ...

Demo Board 

 

LTspice: SOAtherm 指导

Dan Eddleman - 高级应用工程师 Oct 8th 2014
在高功率级别上,验证热插拔设计未超过 MOSFET 的能力范围是一项挑战。 幸运的是,热特性和 SOA 可在 LTspice IV® 等电路仿真器中进行建模。LTspice 中的 SOAtherm-NMOS 符号包含了一个由凌力尔特开发并旨在简化此项任务的 MOSFET 热模型结集。这些热模型可用于验证 ...

Blog Post Video LTspice 

 

DC1575B - LTC4362CDCB-2 Demo Board | Monolithic Overvoltage and Overcurrent Protector with Auto-Retry

Sep 23rd 2014
Demonstration circuit 1575B features the LTC®4362, a monolithic overvoltage/overcurrent protector that safeguards 2.5V to 5.5V systems from power supply overvoltage. It is designed for portable devices with multiple power supply options including wall adaptors, car battery adaptors and USB ports. ...

Demo Board 

 

DC2150A-C - 28V, 5A MIL-STD-1275D Surge Stopper [Featuring LTC4366HTS8-2 and LT4363HS-2]

Sep 22nd 2014
Demonstration circuit 2150A uses the LTC®4366-2 and LT4363-2 surge stoppers to satisfy MIL-STD-1275D. This specification, created by the United States Department of Defense, sets down requirements of electrical systems powered from a military vehicle’s 28V power supply. DC2150A’s output voltage is limited to ...

Demo Board 

 

LTC4252B-1 –48V/2.5A 热插拔控制器

Sep 2nd 2014
LTC4252 负电压热插拔 (Hot Swap) 控制器允许在带电背板上安全地进行电路板的插拔操作。输出电流由 3 个电流限制级来控制:一个定时电路断路器、有源电流限制和一条快速前馈通路 (用于限制最坏情况灾难性故障条件下的峰值电流)。 ...

Circuit LTspice 

 

4μA I Hot Swap Controller Protects Batteries from Voltage & Current Faults

Aug 25th 2014
MILPITAS, CA - August 25, 2014 - Linear Technology Corporation introduces the LTC4231, an ultralow quiescent current (IQ) Hot Swap™ controller, enabling safe board or battery insertion and extraction from 2.7V to 36V systems. The LTC4231 controls an external N-channel MOSFET to gently power up board capacitors, avoiding sparks, ...

Press Release 

 

LTspice: Modeling Safe Operating Area Behavior of N-channel MOSFETs

Dan Eddleman - 高级应用工程师
Gabino Alonso - 市场策略工程师
Aug 22nd 2014
Introduction Often the most challenging aspect of Hot Swap™ circuit design is verifying that a MOSFET’s Safe Operating Area (SOA) is not exceeded. The SOAtherm tool distributed with LTspice IV® simplifies this task, allowing a circuit designer to immediately evaluate the SOA requirements of an application and ...

Blog Post LTspice 

 

LTC4211 单通道 5V 热插拔控制器

Aug 4th 2014
LTC4211 是一款热插拔控制器,允许在带电背板上安全地进行电路板的插拔操作。一个内部高端开关驱动器用于控制一个外部 N 沟道 MOSFET 的栅极,以获得 2.5V 至 16.5V 的电压电源范围。LTC4211 在启动期间 (其具有一个可编程持续时间) 提供了软起动和浪涌电流限制功能 ...

Circuit LTspice 

 

LTC4217 单通道 12V、1.5A 热插拔控制器

Aug 4th 2014
LTC4217 是一款热插拔应用的集成解决方案,允许电路板在带电背板上安全地插入和拔出。该器件把一个热插拔控制器、功率 MOSFET 和电流检测电阻器集成在单个封装中,以满足小型化应用的要求。一个专用的 12V 版本 (LTC4217-12) 包含预设的 12V 特殊门限,而标准器件 ...

Circuit LTspice 

 

LTC4364-1 具理想二极管的 4A、12V 过压输出稳压器可在 Vin 承受 1ms 的 200V 瞬态电压

Aug 4th 2014
LTC4364 浪涌抑制器具有理想二极管控制器,可保护负载免遭高电压瞬变的损坏。通过控制一个外部 N 沟道 MOSFET 传输器件两端的电压降,该器件可在过压过程 (例如:汽车中的负载突降) 中限制和调节输出。另外,LTC4364 还包括一个定时的电流限制电路断路器 ...

Circuit LTspice 

 

LTC4261 具有 I2C 和 ADC 的 –48V/200W 热插拔控制器

Aug 4th 2014
LTC4261 / LTC4261-2 负电压热插拔控制器允许在带电背板上安全地进行电路板的插拔操作。通过采用一个外部 N 沟道传输晶体管,能够使电路板的电源电压以一种可调速度斜坡上升。这些器件具有可独立调节的浪涌电流和过流限值,旨在最大限度地减小启动、输入阶跃和输出短路期间传输晶体管所承受的应力 ...

Circuit LTspice 

 

单输出多相转换器的 MOSFET 故障保护

Mike Shriver - 应用工程师 Mar 19th 2014
对于当今许多领先的通信、网络、计算机和工业系统中的低输出电压轨而言,其必须专为满足 “提高负载电流”、“提高效率” 和 “不断缩小电路板面积” 这些互为竞争的要求而设计。对于负载电流很高的场合,最有效的方法是把两相或更多的相位连接在一起 ...

Video 

 

DC1625A-D - LTC4227CUFD-4 Demo Board: Dual Ideal Diode & Single Hot Swap Controller with Fault Auto-Retry and 1.6ms On Delay

Mar 5th 2014
Demonstration circuit 1625A is intended to demonstrate performance of the LTC4227-1/LTC4227-2/LTC4227-3/ LTC4227-4 dual ideal diode and Hot Swap™ controller. Each rail has an individual ideal diode. Ideal diode outputs are connected to the load through a single Hot Swap circuit.   ...

Demo Board 

 

DC1625A-C - LTC4227CUFD-3 Demo Board: Dual Ideal Diode & Single Hot Swap Controller with Fault Latch-Off and 1.6ms On Delay

Mar 5th 2014
Demonstration circuit 1625A is intended to demonstrate performance of the LTC4227-1/LTC4227-2/LTC4227-3/ LTC4227-4 dual ideal diode and Hot Swap™ controller. Each rail has an individual ideal diode. Ideal diode outputs are connected to the load through a single Hot Swap circuit. ...

Demo Board 

 

DC1555C-B - LTC4365CTS8-1 Demo Board | High Voltage NFET Driver for UV, OV and Reverse Supply Protection with 1ms Fault Recovery

Jan 6th 2014
Demonstration circuit DC1555C is intended to demonstrate the performance of the LTC4365 and LTC4365-1 Undervoltage, Overvoltage and Reverse Supply Protection Controllers. The LTC®4365/LTC4365-1 protect circuits from input voltages that may be too high, too low or negative. It operates by controlling the gates of two back-to-back ...

Demo Board 

 

DC2062A-A - LT4363IDE-1 Demo Board: 12V System ISO-7637-2 Surge Stopper, Latch-Off Version

Oct 21st 2013
DC2062A-A - Demo Board for:LT4363 - High Voltage Surge Stopper with Current Limit ...

Demo Board 

 

DC2062A-B - LT4363IDE-2 Demo Board: 12V System ISO-7637-2 Surge Stopper, Auto-Retry Version

Oct 21st 2013
DC2062A-B - Demo Board for:LT4363 - High Voltage Surge Stopper with Current Limit ...

Demo Board 

 

DC2060A - LTC4229IUFD Demo Board: Single Ideal Diode and Hot Swap Controller

Aug 28th 2013
DC2060A - Demo Board for:LTC4229 - Ideal Diode and Hot Swap Controller ...

Demo Board 

 

DC1555B - LTC4365CTS8 Demo Board: High Voltage NFET Driver for UV, OV and Reverse Supply Protection

Apr 22nd 2013
DC1555B - Demo Board for:LTC4365 - Overvoltage, Undervoltage and Reverse Supply Protection Controller ...

Demo Board LTspice 

 

DC1627A-B - LTC4226CUD-2 Demoboard : Dual Hot Swap Controller with Auto-Retry

Jan 16th 2013
DC1627A-B - Demo Board for:LTC4226 - Wide Operating Range Dual Hot Swap Controller ...

Demo Board 

 

DC2027A-A - LTC4364DE-1 Demoboard: 12V Surge Stopper with Ideal Diode, Latch Off

Jan 16th 2013
DC2027A-A - Demo Board for:LTC4364 - Surge Stopper with Ideal Diode ...

Demo Board 

 

DC1627A-A - LTC4226CUD-1 Demoboard : Dual Hot Swap Controller with Latch Off

Jan 16th 2013
DC1627A-A - Demo Board for:LTC4226 - Wide Operating Range Dual Hot Swap Controller ...

Demo Board 

 

DC2027A-B - LTC4364DE-2 Demoboard: 12V Surge Stopper with Ideal Diode, Auto Retry

Jan 16th 2013
DC2027A-B - Demo Board for:LTC4364 - Surge Stopper with Ideal Diode ...

Demo Board 

 

DC787A-B - LTC4252CCMS-2 Demoboard | Negative Voltage Hot Swap Controller in an AdvancedTCA Application, Auto Retry After Fault

Jan 10th 2013
DC787A-B - Demo Board for:LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 - Negative Voltage Hot Swap Controllers ...

Demo Board 

 

Dual Hot Swap Controller with Flexible Current Limit Rides Through Load Surges without System Interruption

Nov 6th 2012
MILPITAS, CA – November 6, 2012 – Linear Technology Corporation introduces the LTC4226, a dual Hot Swap™ controller, enabling safe board insertion into live 4.5V to 44V backplanes. The LTC4226 controls external N-channel MOSFETs to gently power up the board, avoiding sparks, connector damage and system glitches. Each supply is ...

Press Release 

 

DC1364A-B - LTC4224-2 Demoboard: Dual Low Voltage Hot Swap Controller with Auto-Retry

Oct 23rd 2012
DC1364A-B - Demo Board for:LTC4224-1/LTC4224-2 - Compact Dual Low Voltage Hot Swap Controller ...

Demo Board 

 

DC1899A-B - LTC4228-2 Demoboard | Dual Ideal Diode and Hot Swap Controller, Auto-Retry After Fault

Oct 23rd 2012
DC1899A-B - Demo Board for:LTC4228-1/LTC4228-2 - Dual Ideal Diode and Hot Swap Controller ...

Demo Board 

 

DC1899A-A - LTC4228-1 Demoboard | Dual Ideal Diode and Hot Swap Controller, Latchoff After Fault

Oct 23rd 2012
DC1899A-A - Demo Board for:LTC4228-1/LTC4228-2 - Dual Ideal Diode and Hot Swap Controller ...

Demo Board 

 

DC1850A-B - LTC4366-2 Demoboard | Very High Voltage Surge Stopper with Auto-Retry

Oct 9th 2012
DC1850A-B - Demo Board for:LTC4366-1/LTC4366-2 - High Voltage Surge Stopper ...

Demo Board 

 

DC1850A-A - LTC4366-1 Demoboard | Very High Voltage Surge Stopper with Latchoff

Oct 9th 2012
DC1850A-A - Demo Board for:LTC4366-1/LTC4366-2 - High Voltage Surge Stopper ...

Demo Board 

 

Surge Stopper Integrates Ideal Diode for Comprehensive Protection Against Transient Voltages, Currents & Reverse Inputs & Outputs

Jul 23rd 2012
MILPITAS, CA – July 23, 2012 – Linear Technology Corporation introduces the LTC4364, a surge stopper with ideal diode, providing compact and low-loss protection for 4V to 80V electronics in automotive, avionics and industrial systems. The surge stopper shields downstream electronics from input overvoltages and overcurrent, ...

Press Release 

 

DC787A-A - LTC4252CCMS-1 Demoboard | Negative Voltage Hot Swap Controller in an AdvancedTCA Application, Latch Off After Fault

Jul 3rd 2012
DC787A-A - Demo Board for:LTC4252B-1/LTC4252B-2 LTC4252C-1/LTC4252C-2 - Negative Voltage Hot Swap Controllers ...

Demo Board 

 

Wide Operating Range Ideal Diode Controller Provides Negative Input Protection & Low Current Operation

May 31st 2012
MILPITAS, CA – May 31, 2012 – Linear Technology Corporation introduces the LTC4359 high voltage ideal diode controller that offers a simple low loss replacement to Schottky diodes, along with key features targeted for automotive, avionics as well as solar applications. The LTC4359 operates over a wide 4V to 80V supply range ...

Press Release 

 

DC1935A-B - LT4363-2 Demo Board: High Voltage Surge Stopper with Current Limit, Auto-Retry Version

Apr 24th 2012
DC1935A-B - Demo Board for:LT4363 - High Voltage Surge Stopper with Current Limit ...

Demo Board 

 

DC1935A-A - LT4363-1 Demo Board: High Voltage Surge Stopper with Current Limit, Latch-Off Version

Apr 24th 2012
DC1935A-A - Demo Board for:LT4363 - High Voltage Surge Stopper with Current Limit ...

Demo Board 

 

DC1886A - LTC4232IDHC Demo Board | 5A Integrated Hot Swap Controller with 100ms Turn-On Delay

Apr 20th 2012
DC1886A - Demo Board for:LTC4232 - 5A Integrated Hot Swap Controller ...

Demo Board LTspice 

 

High Voltage Surge Stopper with Current Limit Shields Sensitive Electronics from Transients Beyond 100V

Jan 16th 2012
MILPITAS, CA – January 16, 2012 – Linear Technology Corporation introduces the LT4363, an overvoltage protection controller that provides overvoltage and overcurrent protection to high-availability electronic systems. Supply voltages surge whenever currents flowing through long inductive power buses change abruptly. Also, ...

Press Release 

 

DC1704A - LTC4280 Hot Swap Contr. w/ADC and I2C, 3 GPIOs (req DC590)

Mar 23rd 2011
DC1704A - Demo Board for:LTC4280 - Hot Swap Controller with I2C Compatible Monitoring ...

Demo Board Linduino QuikEval System 

 

DC1625A-B - LTC4227CUFD-2 Demo Board: Dual Ideal Diode & Single Hot Swap Controller with Fault Auto-Retry and 100ms On Delay

Mar 23rd 2011
DC1625A-B - Demo Board for:LTC4227- Dual Ideal Diode and Single Hot Swap Controller ...

Demo Board 

 

DC1625A-A - LTC4227CUFD-1 Demo Board: Dual Ideal Diode & Single Hot Swap Controller with Fault Latch-Off and 100ms On Delay

Mar 23rd 2011
DC1625A-A - Demo Board for:LTC4227- Dual Ideal Diode and Single Hot Swap Controller ...

Demo Board 

 

DC1624A-B - LTC4225-2 Dual Ideal Diode & Dual Hot Swap Controller with Auto-Retry after Fault

Mar 23rd 2011
DC1624A-B - Demo Board for:LTC4225-1/LTC4225-2 - Dual Ideal Diode and Hot Swap Controller ...

Demo Board 

 

DC1624A-A - LTC4225-1 Dual Ideal Diode & Dual Hot Swap Controller with Latchoff after Fault

Mar 23rd 2011
DC1624A-A - Demo Board for:LTC4225-1/LTC4225-2 - Dual Ideal Diode and Hot Swap Controller ...

Demo Board 

 

搜索结果太多,请调整您的选择